Mastering Basic Plumbing When You Install a Bathtub
Mastering Basic Plumbing When You Install a Bathtub
Blog Article
Just how do you feel on the subject of How to Install a Bathtub Yourself?
Installing a bathtub isn't exactly brain surgery, however it does need solid plumbing, carpentry, as well as occasionally, tiling abilities. Changing an old bathtub with a new one is likewise a reasonably difficult task. If the old tub is readily available, the task can move easily; if you have to open a wall to eliminate the old bathtub and position the new bathtub, the job is a lot harder. In either case, the job is within a residence handyman's abilities, although you will certainly require a helper to move out the old tub as well as set in the brand-new one. Ensure you have actually qualified yourself for the task and also are comfortable attempting it. Instead of hiring a contractor to take over a halfway-completed job, it is far better to consider using one prior to you start. Possibilities are you might require a professional plumber to make tube links.
This write-up will certainly help you set up a brand-new bath tub in your bathroom if you have actually currently bought a new bathtub as well as do not need to change the arrangement of your previous water supply pipelines.
Your devices and material checklist must make up the following:
Removing Old Touches
If you need to change old faucets with new ones as a part of your setup, then the first thing you need to do is separate the water. After doing so, switch on the taps to drain pipes any type of water staying in the system. The process of removing the existing faucets can be fairly troublesome because of the restricted gain access to that is frequently the situation.
Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipes to the faucets. Have a fabric ready for the staying water that will certainly originate from the pipes. Once the supply pipelines have actually been eliminated, utilize the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single taps from transforming throughout this process. When the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any old securing substance.
Prior to going on to fit the new faucets, contrast the pipe links on the old taps to the new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is required for the brand-new taps to fit.
Fitting New Taps
If the tails of the new taps are plastic, after that you will require a plastic port to stop damage to the string. One end of the adapter fits on the plastic tail of the tap and the various other end provides a link to the current supply pipes.
If you require to fit a monobloc, after that you will need minimizing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next, place the tap in the placing opening in the bath/basin ensuring that the washing machines are in location between the tap and the sink. Safeguard the tap in position with the producer supplied backnut. When the tap is securely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with typical faucet adapters. The former kind needs to be attached to the tap ends initially, tightening up just by hand. The supply pipes can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Installing the Tub
Utilizing both wood boards under its feet, put the bathtub in the required position. The wooden boards are valuable in equally spreading out the weight of the bathtub over the area of the boards rather than focusing all the weight onto 4 little points.
The next goal is to guarantee that the bathtub is leveled all round. This can be attained by checking the spirit level as well as changing the feet on the bathtub up until the spirit level reads level.
To install faucets, fit the bottom of the furthest versatile faucet connector to the suitable supply pipe by making a compression join; after that do the exact same for the other tap.
Switch on the supply of water as well as inspect all joints and brand-new pipework for leaks and also tighten them if needed. Fill up the bathtub as well as additionally inspect the overflow electrical outlet as well as the typical outlet for leaks.
Lastly, fix the bathroom paneling as described in the producer's instruction manual. Tiling and sealing around the bath tub ought to wait up until the tub has actually been utilized at the very least once as this will resolve it right into its last position.
Getting ready for the Installation
First of all, the supporting structure provided with the bath ought to be fitted (if required) according to the producer's directions. Next, fit the faucets or mixer to the tub. When suitable the faucet block, it is important to ensure that if the faucet includes a plastic washer, it is fitted between the bath and the taps. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the faucets system to prevent strain on the bathtub.
Fit the flexible tap connectors to the bottom of the two faucets utilizing 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet through the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. Ensure you utilize every one of the supplied washers.
Attach the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom ought to now prepare to be fitted in its last setting.
Tiling Around the Bath tub
In the area where the bathroom fulfills the ceramic tile, it is required to secure the accompanies a silicone rubber caulking. This is very important as the fitting can relocate enough to break an inflexible seal, triggering the water to permeate the wall between the bath and the tiling, bring about complications with moisture and feasible leakages to the ceiling below.
You can pick from a variety of coloured sealants to blend in your components and fittings. They are sold in tubes and also cartridges, as well as can securing gaps up to a width of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with twists of soaked paper or soft rope. Bear in mind to constantly load the tub with water prior to sealing, to allow for the activity experienced when the tub remains in usage. The sealer can split relatively early if you do not take into account this motion before sealing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally quickly readily available on the market. It is suggested to fit the tiles using water-resistant or water-proof adhesive and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a reader on How to Install a Bathtub, I was thinking sharing that portion was important. Are you aware of somebody who is intrigued by the topic? Feel free to promote it. I recognize the value of reading our article about How to Install a Bathtub Yourself.
Call, we respond! Report this page